ZyXEL WAC6502D-S Router Login Admin Username, Password, IP

Default Factory Settings of ZyXEL WAC6502D-S Router

IP Address :
Username :
Password :

How to Login to ZyXEL WAC6502D-S Router

ZyXEL WAC6502D-S Router has web interface that provides access router admin panel where you can configure router, change settings and also do diagnostics tests.

Follow these step by step instructions to login to ZyXEL WAC6502D-S Router
  1. Make sure that computer or laptop is connected to router. You can either connect through WiFi or Ethernet cable. If you do not remember WiFi, it is better to connect via Ethernet cable.
  2. After connecting to router, open internet browser. You can use any browser of your choice.
  3. Now type IP address of ZyXEL WAC6502D-S in address bar. IP address of prouter is already mentioned above. Press Enter to load router web interface.
  4. Browser will display router admin web interface and you will see input fields for username and password.
  5. Type in default login username and password shown above and click on Login button.
  6. If everything is correct, you will get access to router admin panel where you can diagnose and troubleshoot router, configure and change settings.

Common ZyXEL WAC6502D-S Login Problems

Above instructions will work most of the times to login to router. But everyone makes mistakes. You might face few generic problems if you do not pay attention to details.

ZyXEL WAC6502D-S Wrong Password
If you get invalid credential or wrong password error, please check that you are correctly typing default login username and password. If you have changed default password, try to remember it. If you can not remember it, you have to hard reset router to factory settings using instructions below.

ZyXEL WAC6502D-S Admin Login Page Not Loading
If router login page is not loading, check network connection again. You can do simple ping test to know that you are connected to router. If network is fine, check IP address carefully. Many people make mistake while typing IP address in address bar of browser.

How to Reset ZyXEL WAC6502D-S Router To Default Settings

Using Reset Button

  1. Remove all networking cables from router.
  2. Power on router.
  3. Locate reset button on the back of router.
  4. Using a clip or any pointed thing like pen, press rest button and hold it pressing for 30-60 seconds.
  5. Release reset button after 60 seconds.
  6. This will reset router to factory default settings. Login to router using default login and password details and make necessary config and change settings to make it secure.

Using Login Admin Panel Interface

  1. Connect router to laptop or computer using Ethernet cable.
  2. Login to router admin panel.
  3. Move to Maintenance tab.
  4. Click on Restore Factory Default / Reset to Default button. It is better to take backup of current settings before changing to factory default settings.
  5. Wait for 60-120 seconds.
  6. Reload login page after 60-120 seconds. You have to now login using default login and password.

ZyXEL WAC6502D-S Router Specifications (Specs)

No of LAN Ports
2
LAN Speed
10/100/1000
CPU 1 Brand
Qualcomm Atheros
CPU 1 Model
QCA9557
RAM 1 Capacity/MiB
256
Radio 1 802.11 Protocols
bgn
Radio 1 Antenna Connector
none specified
Radio 1 Chip 1 Brand
Qualcomm Atheros
Radio 1 Chip 1 Model
QCA9557
Radio 1 MIMO Config
2x2:2
Radio 2 802.11 Protocols
an+ac
Radio 2 Antenna Connector
none specified
Radio 2 Chip 1 Brand
Qualcomm Atheros
Radio 2 Chip 1 Model
QCA9882
Radio 2 MIMO Config
2x2:2
Tag Line
802.11ac Dual Radio Smart Antenna 2x2 Access Point
Global Type
embedded system, access point